TECHNICAL DATA BEY-04
BULLS-EYE
®
ZERO
™
Form: GDH-70
Rev.: 053113
.DESCRIPTION AND USES .
Zinsser
®
Bulls-Eye
®
Zero
™
is a high performance, eco-
friendly water-based primer for interior and exterior
applications. This product has been formulated to meet
clean air regulations to provide a fast drying, low odor
primer/sealer with excellent adhesion, enamel holdout and
stain blocking properties.
Bulls-Eye Zero delivers the performance of oil-based
primers with none of the odors or solvents that contribute
to poor air quality. Bulls-Eye Zero is excellent for use in
residential, institutional or commercial use in schools,
hospitals, hotels, nursing homes, restaurants, etc.
Use on interior and exterior new or previously painted
drywall, wood (pine, fir, cedar, redwood, plywood, T-111),
cured plaster, masonry (stucco, cement, poured concrete,
concrete block), hardboard, vinyl, PVC, fiberglass, tile,
Metal (aluminum, steel, galvanized metal). Adheres to
tough surfaces, such as chalky exterior siding and trim,
high gloss enamels, old varnish, tile, galvanized metal and
hardboard.
Seals unpainted porous surfaces, extending the coverage
of the topcoat. Bulls-Eye Zero is an excellent under-coater
for oil or latex enamels, and provides high holdout and
smooth sanding surface necessary to prevent variations in
topcoat gloss.
Bulls-Eye Zero locks in stains such as residual nail head
dust, asphalt, creosote, tannin bleed for cedar or redwood,
lipstick, crayon, oil, grease, handprints, most ball point and
felt tip pen marks. When priming over bare cedar or
redwood, allow 24 hours dry time before painting.
Persistent stains may require a second coat.
PERFORMANCE CHARACTERISTICS .
For interior & exterior use
Sticks to all surfaces
Seals common stains
Low odor
Mildew resistant film
Dries in 1 hour
.PRODUCTS .
SKU Description
249019 1-Quart
249020 1-Gallon
249021 5-Gallon
PRODUCT APPLICATION .
SURFACE PREPARATION
Surfaces should be clean, dry, sound and free of any
contamination, mildew, rust or unsound coatings that may
interfere with adhesion. Remove loosely adhered or
unsound coatings. Sand any remaining paint film edges
smooth. If unsure of cleanliness, always wash surface with
household ammonia and water solution, appropriate
cleaning solution or solvent (do not use TSP as a cleaner).
Rinse the surface thoroughly and allow to dry before
application of the primer. Spot prime knots and sap
streaks with Zinsser B-I-N Primer/Sealer.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO
LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS
BRAIN DAMAGE, ESPECIALLY IN CHILDREN.
PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH-Approved respirator to
control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National
Lead Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead.
LIMITATIONS
Bulls-Eye Zero is not recommended for applications to
floors, decks, roof surfaces or any surface subject to
immersion or prolonged contact with water.
APPLICATION
Apply only when air, material, and surface temperatures
are between 50-85ºF (10-29ºC) and the relative humidity
is below 85%. Thoroughly mix to ensure any settled
pigment is re-dispersed before using. In most cases only
one coat is necessary to prime most surfaces. If excessive
absorption occurs over very porous substrates a second
coat may be necessary. Spot priming is recommended
only under high-hiding topcoat finishes. For best results,
prime entire surface before painting.
Apply with a synthetic (nylon, polyester or blend) bristle
brush, roller, or airless sprayer. Follow manufacturer's
instructions when using spray equipment. For airless
spraying use a .017" tip at 2000 to 2500 psi. Wear NIOSH
approved respirator and provide adequate ventilation.
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals