TECHNICAL DATA ZBZ-01
BONDZ
®
MAXIMUM ADHESION PRIMER
Form: CS2011
Rev.: 012513
.DESCRIPTION AND USES .
Zinsser
®
BONDZ
®
is an acrylic bonding primer designed for
priming difficult to paint surfaces. Use on interior and exterior
surfaces to promote maximum adhesion over building
material plastics, including PVC sheeting & piping, vinyl,
laminated Formica
®
cabinets, fiberglass awnings and garage
doors, tile, glazed block and brick, and non-ferrous metals
such as aluminum doors and window frames, aluminum
flashing and trim, Kynar
®
coated metals, galvanized steel,
glossy oil-based enamels, drywall, masonry, glass, paneling,
painted or unpainted wood, and slightly chalky surfaces.
Apply any top coat finish including oil-based enamels, water-
based acrylics, epoxies, urethanes, and lacquer.
This product is not recommended for application to floors,
decks, surfaces subject to immersion or prolonged contact
with water or below grade applications. It is not recommended
for use on polyethylene, polypropylene, Teflon or nylon
surfaces. DO NOT MIX WITH ANY OTHER PRIMER
.PERFORMANCE CHARACTERISTICS .
• Bonds to all topcoats and hard, dense surfaces
• May be used with all topcoats including solvent-based
and two-component epoxies
• Topcoat in 1 hour with conventional paints; in 6 hours
with epoxies
• Excellent wet adhesion
• Very low odor and low VOCs
• Easy soap and water clean-up
PRODUCTS .
SKU Unit Size
256260 5-gallon
256261 1-Gallon
271198 1-Quart
APPEARANCE .
BONDZ is white but may be tinted to off-white and pastel
shades to improve the hiding power of the topcoat by adding
no more than 2 oz. (59 ml) universal colorant per gallon.
.PRODUCT APPLICATION .
SURFACE PREPARATION
Surfaces should be clean, dry, sound and free of any
contamination, mildew, scaling paint, loose rust, heavy
chalking, excessive oil and other contaminants such as wax
or wallpaper paste which will interfere with adhesion. If unsure
of cleanliness, always wash surface with an appropriate
cleaner or solvent. DO NOT USE TSP. Always test a small
area for acceptable adhesion. For general oil and water-
based stain blocking, use a Zinsser stain blocking primer such
as Zinsser Smart Prime or Zinsser Bulls-Eye 1-2-3
®
Plus.
Spot prime knots and severe stains with Zinsser B-I-N
®
Shellac-based Primer-Sealer before full surface priming with
BONDZ.
WARNING! If you scrape, sand or remove old paint, you may
release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN
DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT
WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a
NIOSH-Approved respirator to control lead exposure. Clean
up carefully with a HEPA vacuum and a wet mop. Before you
start, find out how to protect yourself and your family by
contacting the National Lead Information Hotline at 1-800-
424-LEAD or log on to www.epa.gov/lead.
MIXING
Mix thoroughly to ensure any settled pigment is re-dispersed.
DO NOT THIN.
APPLICATION
Apply only when air, material, and surface temperatures are
between 36-90ºF (2-32ºC) and the surface temperature is at
least 5ºF (3ºC) above the dew point. The relative humidity
should not be greater than 85%.
Mix thoroughly to ensure any settled pigment is re-dispersed
before using. In most cases only one coat is necessary to
prime most surfaces. If excessive absorption occurs over very
porous substrates a second coat may be necessary. Spot
priming is recommended only under high-hiding topcoat
paints. For best results, prime entire surface before painting.
Apply with a natural or synthetic bristle brush, roller, pad or
sprayer. Follow manufacturer's instructions when using spray
equipment. For airless spraying use a .017" tip at 2000 to
2500 psi.
CLEAN-UP
Clean up spills and paint drips with warm soap and water.
Wipe up splatters before they dry. Follow manufacturer’s
directions to clean spray equipment. Dispose of unused or
unwanted product in accordance with local laws regulating
water-based coatings.
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals